As for the clipping graph it goes over the redline when hard cornering and some crashing. Hitting or getting hit by other cars was really strong. I will give it another try later guys.
One thing I know is that before lowering ffb and other settings it was hardwork turning and the road affect made driving straight really hardwork and the road felt like I was driving on a rough surface with dips and ridges, so maybe too much road detail.
Its Abit better now.
Now its All about the fun of learning and you lot on here help ALOT, even a Thicko like me. Just a matter of walking on egg shells till confident not going to do more damage to my rightarm. Maybe the Large Mige for a newby WAS NOT the best option. (lol)
I would suggest even lower settings being that you are finding your way. If I set SimuCube at 100% output, some titles may only have gain / strength at 30% or so; SimuCube at 80% / game output around 50% is usually enough in my case, with +/- 5% for various cars.
In case you aren’t aware, AC and PC2 allow easy FFB-strength adjustments on the fly while other titles use individual-car strength settings. Custom tuning FFB-strength for individual cars in AMS may require some tweaks to the “RealFeel” file for each car but, most should work based on one average FFB-force level.
Some amount of clipping can be useful in regard to safety, as it means that the extreme (contact with opponents or barriers) signals will be curtailed before reaching the wheel. Using a clip-meter is generally one way to determine the point where that occurs.
@IMac if i where you i would put the max strength in simucube @ 50% or even lower. This will be a lot safer and less chance to hurt yourself. And put the ffb in the games higher
I do not know if it’s good, but I feel it correctly
FFB Device Name="none"
FFB Device Name Alternative=“none”
FFB Rumble Pad=“0” // Type of FFB controller: 0=wheel, joystick etc with force feedback, 1 = pad with rumble motor
FFB Gain=“0.8” // Strength of Force Feedback effects. Range 0.0 to 1.0.
FFB Min Force=“0.02” // Minumum force, from 0.0 to 1.0
FFB Min Force Linear Percentage=“0.01” // Minumum force linear percentage
FFB Throttle FX on steer axis=“1” // 0 = Throttle effects on throttle axis, 1 = throttle effects on steering axis.
FFB Brake FX on steer axis=“1” // 0 = Brake effects on brake axis, 1 = brake effects on steering axis.
FFB stationary friction=“0.7” // Amount of friction applied to the steering wheel when vehicle is stationary
FFB stationary friction speed=“2.7780001” // Below this speed the stationary friction starts to be applied, in m/s
FFB steer vibe freq mult=“1.0” // Controls frequency of steering vibration. Recommended: 0.5 to 1.0, 0.0 disables steering vibration.
FFB steer vibe zero magnitude=“0.0” // Magnitude of steering vibration at 0mph (reference point).
FFB steer vibe slope=“0.0” // Slope of line defining magnitude as a function of frequency (used with FFB steer vibe zero magnitude).
FFB steer vibe wave type=“0” // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down.
FFB steer force average weight=“1.0” // How much weight is given to new steering force calculations each frame (0.01 - 1.0). Lower values will smooth out the steering force, but will also add latency.
FFB steer force exponent=“1.0” // Steering force output “sensitivity”. Range 0.0 to infinity. 0.0 to 1.0 = higher sensitivity, greater than 1.0 = lower sensitivity.
FFB steer force input max=“11500.0” // Recommended: 11500 (-11500 if controller pulls in the wrong direction).
FFB steer force output max=“0.5” // Maximum force output of steering force, recommendation 0.8 to 2.0
FFB steer force grip weight=“1.0” // Range 0.0 to 1.0, recommended: 0.4 to 0.9. How much weight is given to tire grip when calculating steering force.
FFB steer force front grip exponent=“0.3” // Range 0.0 to infinity, recommended: around 1.0. Exponent applied to grip weight.
FFB steer force rear grip exponent=“1.0” // Range 0.0 to infinity, recommended: around 1.0. Exponent applied to rear grip loss weight.
FFB steer damper coefficient=“0.1” // Coefficient to use for steering damper. Range: -1.0 to 1.0
FFB steer damper saturation=“1.0” // Saturation value to use for steering damper. Range: 0 - 1.0
FFB steer force balance mode=“0” // Mode for how to add the steering forces together (lateral, load and diff). Acceptable values: 0 = lat + load + diff, 1 = sqrt(lat^2 + load^2 + diff^2), 2 = sqrt(lat^2 + load^2) + diff, 3 = sqrt(lat^2 + (load + diff)^2), 4 = sqrt((lat + load)^2 + diff^2)
FFB steer load multiplier=“0.3” // Multiplier for vertical load on front tires. Range: 0 - infinity
FFB steer lateral multiplier=“2.0” // Multiplier for lateral forces. Range: 0 - infinity
FFB steer rack factor=“0.05” // How much of the lateral forces comes from steering rack. Range: 0 - 1.0
FFB steer load change exponent=“0.95” // Exponent for the change in load on front tires. Range: 0 - infinity
FFB steer load change breakpoint=“1.0” // Breakpoint (value that will not be changed) for the exponent on the change in load on front tires. Range: 0 - infinity
FFB steer spring coefficient=“0.1” // Coefficient for steering spring. Range: 0.0 - 1.0
FFB throttle vibe freq mult=“1.0” // Scales actual engine frequency to force FFB vibration frequency. Suggested range: 0.10 to 0.50
FFB throttle vibe zero magnitude=“0.01” // Magnitude of engine vibration at 0rpm (reference point).
FFB throttle vibe slope=“0.0” // Slope of line defining magnitude as a function of frequency (used with FFB throttle vibe zero magnitude).
FFB throttle vibe wave type=“0” // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down.
FFB rumble strip magnitude=“0.9” // How strong the rumble strip rumble is. Range 0.0 to 1.0, 0.0 disables effect.
FFB rumble strip freq mult=“2.0” // Rumble stip frequency multiplier 1.0 = one rumble per wheel rev.
FFB rumble strip wave type=“0” // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down.
FFB rumble strip pull factor=“0.0” // How strongly wheel pulls right/left when running over a rumble strip. Suggested range: -1.5 to 1.5.
FFB jolt magnitude=“0.0” // How strong jolts from other cars (or walls) are. Suggested Range: -2.0 to 2.0.
FFB shift jolt magnitude=“1.0” // How strong jolts you get from shifting. Suggested Range: -2.0 to 2.0.
FFB shift effect duration=“0.05” // Duration of shift effect in seconds
FFB slip effect=“0.2” // Slip effect, from 0.0 to 1.0
ffb slip freq multiplier=“1.0” // Slip effect frequency. 1.0f = 1 cycle per wheel rev
ffb slip wave type=“0” // Slip effect wave type
FFB pedal throttle vibe zero magnitude=“0.1” // Throttle pedal vibration at 0rpm (reference point)
FFB pedal throttle vibe slope=“0.15”
FFB pedal throttle slip vibe=“1.0” // Throttle pedal vibration on tire slip
FFB pedal brake slip vibe=“1.0” // Brake pedal vibration on front tire slip
FFB pedal brake vibe slope=“15.0” // Slope for brake pedal vibration based on speed and braking %
There is always a bug with collision effects, so always set it to 0 .
Now that all the effects of RaceRoom are very well managed thanks to the excellent work of Mika, I would like to find the correct settings, but I can not do it.
I wanted to know what the different sliders in DirectInput Effect Setting correspond to:
i actually don’t use any of those effects. the clean ffb is the best in my opinion instead of fake effects.
that way you only feel the real things who are there. personally i am not interested in fake road effects or engine vibration that add random vibration. there is enough real track detail. but the road texture is totally smooth. but bumps you do feel.
only the sine wave effect does something in RRE if i am correct
In the simucube controller I use unlimited tbw, 1080°, damping 2 and friction 1, the rest default
In game 60% strength, the rest at zero, then I change the ffb strength for each car between 60 to 80%
In assettocorsa.ini enable gyro=1 damper min level 0,1 damper gain 1.0
in ff_post_process.ini type=gamma enable=1 value=1.3
Enjoy
Tried lots of recommended ingame, simucube settings from others who dont have the issue, yet I can not get rid of the cog gear feeling when turning or the sand grinding sound.
Im beginning to wonder if the issue is with my mige kit. I even tried the sine affect at a few settings that others recommemded and it turns the wheel into a big smooth vibrating massaging my hands wheel and when turning corners the car feels like the wheels are buckled. Oh the oscillation while driving straight is Really bad.
Only thing I have changed lastnight as a last attempt to fix it was in ioni/granity it was set to 13.44A so upped it to 23.25 and 25.00A (mcc/mmc?) because that appears to be what most have it set to.
One thing I read is power limit in granity/ioni (think that what called) a few settings i read said set to ‘0’ no limit (unlimited) if running sdr 480-720w psu yet mine is set to 480 ? This is what was set to by the retailer, who also set the mcc or mmc to 13.44A.(cant remember which one)
Not used it for days while waiting for latest simucube 0.9.4 with the updated granity 1.70.
