Fault Location 442001

Simucube 2
1

Hello,

I just bought a Simucube 2 Pro and installed the hardware and software. Everything seems working fine so i loaded the standard iRacing profile and went for a testdrive. After 2 corners the FFB was gone. I returned to the True Drive software and i got the error message “Motor Faults: Over current! Power Stage Forced Off (Fault location ID: 442001)”.
If i push/pull the e-stop, or turning the power off/on, the error is gone but now as soon as i turn the wheel (in Windows) the error is back again.
Can anyone help me with this?

Thank you in advance!

2

Are both power bricks properly connected to the sc2 base and to the wall sockets?

3

I had that error with my SC2 Sport, not a power problem but software side. Read the post above to learn new things

Edit: May be not the Same case but was the Same error code

4

Yes, i believe so. Double checked it, blue lights are on at both power supplies

5

Hello, has anyone found problem solution for this?

One of my Simucube 2 sports started showing this error when I turn it on.

I press ON, there is a quick beep and motor just starts oscillating like crazy for a second and error comes on: "Motor Faults: Over current! Power Stage Forced Off (Fault location ID: 442001)”.

I have installed the latest software this morning, nothing helps…

error.txt (5.2 KB)

6

Hi,

Does the wheel centerpoint also drift when this happens? I see you have reset the center point in the log.

7

I reset it just to try it going again because when the wheel starts up its instantly hitting max rotation to the side and wheel recognition on TD dissapears, motor fault comes up. I reset it with the emergency button but the moment I deactivate it just goes mad again instantly.

8

Try starting SC2 with estop ON, delete all profiles or the new ones after the problem started, then reset/save new wheel center. Save settings to SC2.

Restart device with estop OFF

9

@LAR555 can you try downgrading to release 2020.10 to see if it has any different behavior?

10

hello, thanks but didn’t help.

11

Downgraded to 2020.10 but same thing happened…

Timestamp : 2280
Wireless: State change : 2
Simucube Boot : 1
Simucube Boot : 0
Simucube Boot : 30
Flash settings data loaded : 0
First-time drive initialization : 0
Rewriting default read-only profile with new values : 0
Initial config has been previously performed. Initializing Drive. : 0
State: Initializing Drive : 0
Drive Firmware update : 0
Timestamp : 8746
Wireless: State change : 3
Timestamp : 9262
Wireless: State change : 3
Timestamp : 9565
Wireless: State change : 3
Timestamp : 10420
Wireless: State change : 3
Drive firmware updated successfully : 0
Command: Request profile number : 0
Command: Request profile name for profile : 0
Command: Request profile byte data for profile : 0
Command: Request hardware settings : 0
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 0
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 1
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 2
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 3
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 4
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 5
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 6
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 7
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 8
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 9
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 10
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 11
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 12
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 13
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 14
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 15
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 16
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 17
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 18
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 19
Command: Request analog input settings : 0
Command: Request bytedata for analog profile : 20
Command: Set calibrated analog axis mode : 0
Drive init stage 1, position : 2312168
Read MMC value from Drive : 15500
Read Motor Resistance value from Drive : 1200
Read CPR from Drive : 4194304
Read Drive Version ID from drive : 40000
Simucube 2 Serial Number : 9872
SM Watchdog disabled successfully : 0
Successfully applied DRC data to Drive : 0
Read MMC value from Drive : 15500
Read Motor Resistance value from Drive : 1200
Read CPR from Drive : 4194304
Read Drive Version ID from drive : 40000
Simucube 2 Serial Number : 9872
Waiting for servo to be ready : 0
Drive init stage 3, position after faults cleared : 2312168
Drive init stage 4, phasing, current position : 2312165
Drive init stage 4, phasing, current position : 2312173
Drive init stage 4, phasing, current position : 2312179
Drive init stage 4, phasing, current position : 2580947
State: Drive initialization was successful : 0
State: Set baudrate : 0
SM Watchdog enabled successfully : 0
SMBus baudrate initialized successfully : 4500000
State: Before operational - calculating new constant values : 0
State: Operational : 0
Command: Event log download request : 0

13

Hi there ! Did you finally fixed it ?

14

Hi Mika ! I got a problem with my simucube 2 pro (first batch if it can help) I upgrade from 2020.1 to 2021.9 with truedrive .But after this i realize after a couple of wheel base crashed in American truck simulator and wrc that something is wrong with the rotation because its dont stop at the profile rotation maximum .So i just update to the last version and did’nt fixed it .I deleted every single profiles and even the default one in offline profile… reset the base with and witout the emergency button like someone said earlier… Din’nt work .So i tested it further.Recreate a default offline profile and when i am in the wheel status the software can pass throught the 450 degrees (half of 900) but i can continue to turn the wheel physiquely and the green light come after 450 degree and if i continue the wheel disconect with the error 442001. i can put the wheel degree at 2160 exemple for ats and the green light coming around 1130 …

Thanks in advance !

15

There were some releases with sometimes buggy end stops on the wheel. If the same thing is happening on the latest release, can you please show your settings also?

If the servo drive system is in a fault state, then of course it doesn’t produce torque and you are able to turn over the endstop and at that point, the led changes color. Eventually the servo drive triggers another fault with completely senseless over rotation.