AUGURY Settings

Simucube 1 Simucube 1 Questions
1

I have a question regarding the AUGURY 20NM regarding NO TOP LEFT AND RIGHT DETECTED.

My hardware configuration:

  • IONI PROHC.
    -(10000ppr) (130ST-M10010
    -MMO´S
    -NDR-480-48 (480W) (versión estandar).

Problems arise when:
-TOP LEFT AND RIGHT NOT DETECTED

How it behaves:
-From the start. First plug after unboxing the product. All connected .The USB is on a 2.0 plug
-Turning the power .
-The wheel turn left right and stop after a few second
-The process requested by the AUGURY TEAM is to turn to the top left the wheel til the “top” is get
-But the top never comes after 10 spin…

Does anyone had the problem ?

Thanks for the support.

2

If using MMOS, you more than likely do not have Use Index Checked in the Set-up along with the set center point.

If young the SimuCUBE firmware, what type of indexing method are you using.

Basically it just seems like your indexing is not being located.

3

Thank you for the reply.

Sorry for my basic english “technical” speaking

Here is where i am:

DFU

4

Does the red usb plug on the bottom left go green after you power up the wheel?

Should look like this:
4617-a088068a30fcea4a046211f27c55d927

The wheel goes left/right/left/right… Its called phasing. Dont touch it, just leave it until it stops.

Then you center your wheel and click “center steering and save offset” you only have to do this once.

5

@McErono, yes the phasing was okay .

But on the AUGURY instructions , they say , after the “balancing left right and stop”, to turn to the top left the wheel and then to the top right…

Here is the problem: i have no top left or right

Second step:
-Seing this problem, unfortunetly i´ve “clicked” on the DFU Mode and now the usb plug on the buttom is red…

6

I have no idea what they mean by „top left top right“, its a wheel, there is only right and left :wink:

first, to get out of the DFU mode, open the windows device manager, under usb controllers there should be a device called DFU something. delete that device. mmos should show a green usb plug again.

when the wheel is powered on and the green usb plug is showing up, you should see the „center steering and save offset“ text on the top. center your wheel, click on the small circle in front of the text.

if all is ready, you should power on the wheel, it phases and then you have to move the wheel over the centerpoint to initialise the wheel. there is no rule where the real centerpoint of your servo is, it depends how you mounted it etc. so you just turn the wheel 180deg left or right. to see if your wheel is ready you can activate the desktop effect damper. as soon as you turn the wheel over the centerpoint and the wheel is ready, it gets heavy because the desktop effect damper is activated.

maybe this video does help to understand better:

at 1:50 the wheel does phase and then he turns the wheel left and right to find the centerpoint of his servo.

1 Like
7

The top left and right is the : steering lock default sorry :wink:

8

make sure the „use encoder index“ is checked in the mmos setup window.

9

“Use encoder index” is checked

But i have no DEVICE CALLED DFU something

USB
USB534×776 24.6 KB

The way you explain, so there is no need to first find the steering lock before clicking to “center steering”?

10

the steering lock/stop is given by the 900degrees you have set in mmos. so you can turn the wheel 450degrees left and 450degrees right but first you have to define the centerpoint by centering your wheel. otherwise mmos does not know where to set the so called bumpstops (steering stop).

do you see the DFU device under windows, settings, devices, connected devices?

11

Okay,

so …
Devices check and okay :wink:

01

Setup okay:

02

And you say:
so you can turn the wheel 450degrees left and 450degrees right but first you have to define the centerpoint by centering your wheel. otherwise mmos does not know where to set the so called bumpstops (steering stop).

Center point is define by clicking on it…But no steering stop

12

that looks fine now. after phasing just turn the wheel 180degrees left, then 180degrees right. at the moment it says „center steering“ but it should change to „center steering and save offset“ after you turned the wheel 180degrees left/right.

13

Done…But : no steering stop

0005

14

you did hit the “center steering and save offset” while your wheel was centered?

its all fine now from what I can see, thats what it should look like. I have no idea why you can’t feel the bumbstops. but the wheel is working now?

try reducing the steering angle to 360° just to check again, you should feel the bumpstop after 180° left/right then.

15

you did hit the “center steering and save offset” while your wheel was centered?
yes

but the wheel is working now?
Yes it looks like :slight_smile:

try reducing the steering angle to 360° just to check again, you should feel the bumpstop after 180° left/right then.
Absolutly no bump stop at all …

000525

16

I mean you wont need the bumpstops, you will never feel them ingame because you don’t turn the wheel 900° but still… very strange, never seen or heard of it!? you can turn your wheel indefinitely?

17

Absolutly…Indefinitely… :slight_smile:

18

Try turning the gain up to about 50 - 60x and see if you can feel them… You may have the gain set low enough where you can barely recognize they are there…

19

@bsohn, thanks for your suggestion, but nothing happend

20

Hmm weird… usually if the end stops aren’t working it indicates that the counterpoint index cannot be found which is weird since your settings indicate basically that it is found…